收藏本站
P ATENTS , C ONNECTIONS , A SSEMBLY , AND P ACKAGING
P ATENTS
Lamina’s light engines may be covered by pending patents and/or one or more of the following U.S. and/or
International patents 5876536, 6709749 B, 595880, 6017642, 5565262, 5681444, 5653834, 5581876, 5847935,
5514451, 5747931, 5925203, 5725808, 5929510, 5858145, 5866240, 5953203, 6055151, 614076, 6011330,
6399230, 6914501, 6168490, 6191934, 614075, 6160469, 6300267, 6471805, 6518502, 6739047, 6720859,
6759940, 6518502, 6670856 B1, 6720859, 6713862 B2, WO 00/47399, WO 00/26152, WO 98/19339, 5082804,
ZL99808762.9, 69623930, 69628549, 69629572, 805785, 69628549, 843621, 932500, 805785, 812258,
843621, 932500, 805785, 812258, 843621, 932500, 805785, 812258, 843621, 932500, 3327556, 3267299,
3226281, 3405545, 320630, 295695, 284068, 546471, 805785, 812258, 843621, 6455930, 6759940, 6713862,
7095053, 7098483.
E LECTRICAL C ONNECTIONS
LED light engines are available with or without Lamina’s EZConnect board. EZConnect adapter boards have
AMP connectors for solderless connections to Lamina’s wiring harness.
As with many electrical devices, non-acid RMA type solder flux should be used to prepare the solder pads before
application of solder. Ensure proper strain relief of wires attached to the light engine to prevent damage to the
light engines solder pads. For more information refer to Lamina’s connection application note AN-05 which can
be found on the website at www.laminalighting.com.
Functional test: Parts may be tested using a constant current source set at 25% of Drive Current for no more
than two seconds without heat sink.
1.
2.
Optical and electrical specifications are given for the specified drive @ 25oC junction temperature.
When using constant current LED drivers with high compliance voltage (Advance, LEDworks, etc. or a
custom driver) the output of the supply must be connected to the part before power is applied to the input
of the supply.
A SSEMBLY R ECOMMENDATIONS
Lamina’s Series Light Engines are designed for attachment to a heat sink with conductive epoxy, or screw down
for flange mount devices with thermal grease in the joint. For attachment using screws, a 2-56 UNC round head
or metric equivalent M2 X 0.4 cheese head screw, 18-8 SS is recommended. When mounting the light engine,
positionthethreescrewsinthecenterofeachofthethreeslots.Tightenthethreescrewsevenly,firsttoabout
0.89 inch pounds (10 Newton-centimeter), and then tighten each to a maximum torque of 4 inch pounds (45
Newton-centimeter). Flatness requirement of the surface that the light engine is mounted to is 0.001 inch/inch
(1mm/meter).
All specifications are based on mounting the LED array to a heat sink using the specified hardware and thermal
grease (e.g. Wakefield P/N 120). The heat sink must meet the specified flatness requirement. Mounting using
screws and thermal tape may damage the device.
R ECEIVING P ARTS AND P ACKAGING T RAYS
Your parts will arrive in either custom fitted trays or on easy to use tape and reel packaging. This packaging
was designed to provide the necessary protection during shipment and to take up the least amount of space in
your storage area.
Notes
1. This product uses silicone materials for superior optical performance. Do not expose the part to fluids that
may react with silicone compounds. See Dow Chemical Form 45-0113D-01, Silicone Fluid Resistance
Guide.
2.
3.
4.
Ray trace models are available upon request.
Lamina may make process or materials changes affecting the performance or other characteristics of our
products. These products supplied after such changes will continue to meet published specifications, but
may not be identical to product supplied as samples or under prior orders.
All specifications are based on mounting the LED array to a heat sink using the specified hardware and
thermal grease Wakefield P/N 120. The heat sink must meet the specified flatness requirement. Mounting
using screws and thermal tape may damage the device.
?2008 L AMINA L IGHTING I NCORPORATED
A TLAS TM S ERIES LED L IGHT E NGINES FM-0167 R EV 05.21.08
  
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
NT-42C1-0485 LIGHT ENGINE ATLAS GREEN
NT-42B1-0484 LIGHT ENGINE ATLAS BLUE
550-3007 LED 5MM RT ANG RED/GRN DIFF PCMT
ASFLMPC-125.000MHZ-LR-T OSC 125.000 MHZ CMOS MEMS SMD
5.00100.1410000 CONTACT BLOCK SCREW 2NC AG
550-5104 LED 5MM VERT SUP DIFF RED PCMNT
NT-41A0-0482 LIGHT ENGINE ATLAS RED
76MRSB09S SWITCH DIP RECESS RCKR SLD 9POS
相关代理商/技术参数
NT4-7PA 功能描述:机架和机柜配件 NUT PKG 25 RoHS:否 制造商:Bivar 产品:Rack Accessories 面板空间: 颜色:Black
NT480 制造商:LUMINIS 制造商全称:LUMINIS 功能描述:Wall mount
NT485 制造商:LUMINIS 制造商全称:LUMINIS 功能描述:Wall mount
NT4886S2 制造商:IPD 功能描述:
NT491212 制造商:Kings Electronics 功能描述:
NT491715 制造商:Kings Electronics 功能描述:
NT49531 制造商: 功能描述: 制造商:undefined 功能描述:
NT4R1600 功能描述:PCI Express / PCI 连接器 MM60 STAND OFF 5.9MM NUT RoHS:否 制造商:JAE Electronics 系列:MM60 产品类型:PCI Express 位置/触点数量:52 安装角:Right 安装风格:SMD/SMT 端接类型:Solder Pad 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold